American West Metals Limited and Aston Bay Holdings Ltd believe a combination of dry sensor-based sorting and wet jigging can significantly reduce the size of the copper concentrator they plan to build at the Storm copper project on Somerset Island, Nunavut, Canada.
The two companies hold 80:20 interests in the project, with the assessment of preconcentration technology coming with the results of prefeasibility study (PFS) on the asset.
The PFS was prepared by Sacré-Davey Engineering Inc with specialist contributors and supports the first reserve estimate for the project.
The initial 1.3 Mt/y development scenario, which comes with $81 million of initial capital, includes a reserve of 12.58 Mt at 1.2% Cu and 3.7g/t Ag for a contained metal content of 151,000 t of copper and 1.5 Moz of silver. It also outlines a mine life of 11 years at an average of approximately 10,000 t/y of copper with the potential to increase both the scale of the mining operation and the mine life through expansion, American West says.
Storm is planned as a conventional open-pit operation run by a mining contractor. Production is planned with hydraulic excavators of approximately 90-t class and nominal 60 t rigid-frame haul trucks, supported by drilling, blasting and ancillary equipment. The pits are mined in stages to bring higher-grade ore and lower stripping forward. Chinook is mined first because its ore reaches the target recovery at the lower throughput of the staged plant start-up. Total material movement is about 11.3-11.6 Mt/y from 2032 to 2036.
Mining and processing are scheduled year-round, with monthly productivity factors for Arctic conditions, including periods below about -40°C. Scheduled material movement is held at about 80% of nominal fleet capacity. Ore above 0.5% Cu is generally sent to the process plant; lower-grade ore above the deposit cut-off is stockpiled for later treatment. Ore stockpile inventory peaks at about 2.9 Mt in 2036; about 2.1 Mt remains when mining ends in July 2038 and is processed by April 2040. American West advises that stockpile rehandle is included in the operating cost estimates; no separate rehandle cost is carried.
Total material mined is 83.28 Mt, including 70.70 Mt of waste (inferred resources are treated as waste) and 12.58 Mt of ore, for a life of mine strip ratio of 5.6:1.
The process plant is planned to be built in stages, starting with Chinook ore in April 2030 and expanded in Year 2 to process at the planned throughput rates. Run-of-mine ore is crushed in three stages and screened and upgraded by dry sensor-based sorting (X-ray Transmission) of the coarse size fraction (about 40 mm to 6 mm in size) and wet jigging of the intermediate fraction (about 6 mm to 1 mm). The fine fraction is milled and treated by flotation. The final product is a copper-silver concentrate averaging about 15% Cu and 46 g/t Ag.
The flowsheet is based on pre-concentration of the ore at a coarse size. Dry sorting rejects about 79% of the plant feed as waste before any grinding, the study states. Less than 10% of the feed is milled and treated by flotation. As a result, the grinding and flotation circuit is small compared with a conventional copper concentrator of the same throughput, it states.
Metallurgical test work from 2022 to 2025 on Chinook and Cyclone samples covered sensor-based sorting, gravity separation and flotation mineral recovery processes. Sorting produced a product of at least 10% Cu, including from low-grade samples. Jigging and flotation recovered additional copper from the fines. The design target is a concentrate grade of 15% Cu. Copper recovery varies with feed grade and deposit origin.
At the mine-plan head grades, the estimated copper recovery is 70.4% in years 1 and 2, 68.8% in years 3 to 9 and 55.8% in years 10 and 11 when processing the stockpiled low-grade material.
- Multiple work streams are planned to advance the project during 2027 for both the definitive feasibility study and for resource/reserve growth, including:
- Resource and exploration drilling;
- Geotech and metallurgical drilling and test work;
- Final engineering design; and
- Sealift of fuel and other supplies for pre-development.
Dave O’Neill, American West’s Managing Director, said: “Against a backdrop of strong copper prices and growing demand for capital-efficient precious metals projects, we believe Storm offers a compelling combination of low capital intensity, technical simplicity, substantial resource inventory and significant exploration upside. The PFS provides a strong foundation for advancing Storm towards becoming a new Canadian copper producer and delivering long-term shareholder value.”
The post American West, Aston Bay look to pre-concentration tech for smaller Storm copper concentrator appeared first on International Mining.

